95n House and Home

Talks about Home Interior Design and Furniture

Foam Board Insulation for your Enclosed Carport, Garage or Metal Building

Among the most effective and easy-to-install insulation choices for your enclosed carport, garage or metal building is foam board. The same stuff that NASA has used to insulate a space shuttles external tank, keeping its liquid hydrogen fuel at minus 423F and its liquid oxygen tank at near minus 297F to prevent ice buildups on the inner fuel tanks exterior surface, can be used to keep your metal carport toasty in the wintertime and cool during the summer.

While fiberglass insulation works by slowing down the rate of passage of heat into your home during hot summers and out of your enclosed carport, garage or metal building in winter, foam board insulation brings that passage to a halt by completely sealing all cavities and spaces in your structures walls. These unsealed voids are the primary source of energy loss, which means more money out of your pocket and into your energy providers coffers.

Enclosed car port foam board is a bit more expensive than fiberglass and may require professional installation. But its “R value” (its measure of thermal resistance) can be three times that of fiberglass. The higher a structures R value, the better its insulations effectiveness. If you plan to spend lots of time in your carport, garage or metal building (for instance, if you plan to use it as a workshop, office or recreational room), the long-term energy cost savings over fiberglass can be significant.

Foam board insulation can be applied to steel carports, enclosed garages or pole building in several ways: as rigid panels attached to your carport, garage or metal building inner walls or as a chemical mixture prayed from aerosol containers or a pressure sprayer (A third method involves foam board in the form of loose beads poured into masonry blocks in more traditional construction). Rigid foam board insulation typically comes 4×8 sheets and can be cut to fit your structures walls using a craft knife or fine toothed handsaw, then applied to your walls using construction adhesive. Two important notes: 1) Because foam boards absorb water vapor, you must cover the insulation with a moisture or vapor barrier and 2) because foam board is flammable, building codes in virtually all areas require that it be covered with fire resistant paneling or drywall.

Foam board also can be sprayed directly on to your walls via aerosol containers or pressure sprayers. It is recommended that you hire a professional installer for this method, as it can involve complex equipment. And because foam boar seals your enclosed carport, garage or metal building so tight, an air exchange may need to be installed. However, this results in superior indoor air quality because air pollutants such as pollen and dust have no way in. Foam board insulation also can help ward off mold, pest and insects for most enclosed carports.

What Are Fireplace Mantel Plinths

Plinths are square block bases traditionally made from stone used as a support for columns of your building and also have existed for years and years ago. They are known to decorate houses of royalty and still widely used even as much as today.

Really should be fact, plinths today are prevalently used not only as bases for statues, pedestals or monuments but you are also employed in many homes to frame doors, windows, cabinets, and fireplaces in order to name just a few, adding some personal touch to ones home interiors.

Generally employed for aesthetic purposes, plinth blocks now are often made available in a variety of materials which range from plaster, concrete, brick, stone, and wood. Those manufactured from wood can be used to trim a door, window, or fireplace are available in lots of wood types like white pine, poplar, oak, mahogany, maple, and cherry. They may be finished, or unfinished, painted or hand carved and are available in a number of designs that may range from intricate carvings with classic patterns to easy and more functional types.

Regarding a fire, a wooden plinth is directly placed directly under either side of the fireplace mantel to serve as footstalls particularly when the inside height of one’s mantel piece needs to be augmented. This technique usually intends to bring more focus on the mantels framing your fireplace; to offer the space a particular appearance brought about by the design of the fireplace mantel. Sold in pairs, most if not completely fireplace mantel plinths currently available are available in pre-cast and ready for installation. More popular types include pearl mantels, mission oak, medium oak, distressed medium oak and cherry finished. Price tags average from $100- $200.

To learn which plinth pair is simply befitting your mantel, you have to measure the “outside leg to outside leg” measurements and you less the interior opening and divide it by 2 to get the width of every leg. You can definitely you aren’t sure relating to this, you might need an expert to measure them for you personally. Though doable for installation, you may want to hire a specialist or observe security precautions when installing.

Roofing Contractors Mesa AZ

Roof replacement generally is one of the most expensive things a landowner has to discover. Depending on the dimension of the house, a novel roof may be expensive for a few thousand dollars. That’s the reason why it’s important for hiring capable roofing contractor that has a performance record of delivering excellence service. Underneath is a couple of things to think about prior to hiring a roofing contractor for replacing a roof:

1. You have to be sure about the contractor company and that you knows through getting license verification of such company. When the company is legally employed in such industry then will show you the legal license. Be sure to confirm the license number of your company.

2. You need to ask the firm to provide you three reference amounts of previous customers. Call them immediately and have them for the particulars of their work. It’s also wise to get the details about the problems faced by previous customers and also the provided solution of company.

3. Search for multiple agencies supplying similar services. Ask their cost quotation and service list. At least you should collect information on three companies to outcome and will negotiate about prices and services.

4. Ensure together with your insurance firm to clarify the contractor company is standard service provider.

5. Ensure to collect details from local business bureau and browse any grumbles of Roofing contractor Company. When it comes to online portal from the company or sort through search engine to get the exact report of this company.

6. Ask the corporation to provide you the current responsibility insurance policy to defend you if something goes wrong during roofing replacement.

7. Inquire about the company’s relevant permits to start out the roofing building project.

8. Inquire with your friends, family members and cover agent if they have any proposals of your finest quality company.

9. Never ever pay in advance for the work and never pay in cash. When the firm request for advance then do not pay more than 10 percent. Never reimburse anything ahead of time of the project that’s not yet been completed.

10. Read the terms prior to signing the contract and also confirm the price quoted within the agreement. Don’t forget to ask about the types of materials company is going to use for roofing construction.

These mentioned steps will show you to judge the accurate contractor for your roof construction. Having a listing of multiple companies will allow you to get the correct one together with your desired services.

Modern Industries with Quality output

Lethbridge is one of the cities of South Albert province located in Canada. It is a small city consisting of a population of 86,659. Many commercial and residential areas are coming up in the city. Hence for the development of the city like Lethbridge, there are industries manufacturing and supplying domestic hardware products to cater to the needs of the common people. Most of the companies provides services like plumbing, welding, HVAC, heating, roofing and metal fabrication for residential and commercial purpose.

Canada is a high altitude country and hence the weather here is mostly cold. Therefore, people need to keep high end appliance at home, commercial place and at work places to keep the indoor temperature friendly. To come up with a solution to this problem the service providers have brought many products like heaters and boilers. They also cater service to leakages of the roof and rooftops. Hence Lethbridge roofing services is done in various houses and residential premises with premium quality. The service providers provide all types of roofing services like built up roofing, sbs bent up roofing, hot rubberized roofing, single ply EPDM and single ply PVC membrane Lethbridge roofing to the city. They are also into the repairs of the existing rooms and services for new installation. Other roofing services also include waterproofing, commercial air type and vapor barrier roofing.

Other than this, they also provide Lethbridge Heating services where the conventional types of heaters are not used in residences, schools or commercial areas. The conventional types of heaters consumed a lot of space, electricity and maintenance. They are now replaced by Lethbridge Heating services with new heaters like the branded and eco friendly Lennox gas furnaces that are easy to use and also have low maintenance cost. They have distinct features like quiet operation, quality construction, and space saving feature with flexible installation, good performance and low energy bills. They also provide water heaters for hot water bathing and for household work 24 hours a day, even in a cold climate.

Lethbridge HVAC is also known as Heating Ventilating & Air Condition system. This service is latest in technology. Lethbridge HVAC is being used in offices and in school classroom to provide good ventilation to staff at work place and to students in classroom. Lethbridge Metal Fabrication uses technology required in industries for heavy workload. Metal Fabrication is needed to mould the metal and give it a proper desired shape. It is done with the help of plasma heating. They are then cut into proper slices and are finally fabricated. Fabrication is done to products like refrigerator cabinet, shelves and coolers. Kitchen cabinets too are covered in fabrication. Lethbridge Roofing is also done to big structures like hospital roofs.

How You Can Do the Garbage Bag Airflow Test

Nothing beats the coziness of your own home especially during those cold, winter nights. But when you’re freezing in it despite having a furnace then there’s a problem. A good way to check if poor air flow is the concern is to use the garbage bag airflow test.

One of the most common issues with heating and cooling equipment is poor air flow. This problem makes your heating and cooling equipment work like inefficient outdated models and this can waste a lot of your money. The two most common reasons for poor air flow: inadequate duct sizing and a dirty return air filter.

Inadequate Duct Sizing Inadequate duct sizing is usually the result of a poor installation by a contractor who might possibly not have the qualifications to perform proper sizing. This is a very common problem that a homeowner may battle for years to come and could cost thousands of dollars over the life of the equipment. It is extremely crucial that you get references before choosing a contractor.

A Dirty Return Air Filter A dirty return air filter is the easiest problem to fix. Simply change your return air conditioning filter more frequently or utilize a filter that does not restrict air flow. This simple change can lead to huge savings. How You Can Perform the Garbage Bag Air flow Test

Garbage bag airflow test is one of the easiest and cheapest methods to determine the air flow of your furnace registers, bathroom exhaust fan or clothes dryer exhaust. It’s a vital test to pinpoint the reason why your furnace isn’t providing sufficient warm air in your room. This is also important in order to determine whether your newly purchased exhaust is working at its best. The same goes when you’re having major renovations in your home that call for a change in your heating or cooling systems. It’s the cheapest way to check your furnace register and exhaust fans performance as it only requires a garbage bag. This test isn’t a precise measurement of the airflow but it is better than not conducting any test at all.

Here’s how to do the garbage bag airflow test:

1. Secure the mouth of the garbage bag using a tape right into a bent coat hanger or to a cardboard in order to keep it open.

2. Be sure to deflate the bag by crushing it flat.

3. Position the open part of the bag (mouth) over the furnace register or exhaust hood.

4. Using a stopwatch or any gadget track the number of seconds it takes for the bag to fully inflate.

If you’re using a small garbage bag that measures 66 x 91 cm, you should use the information below to determine the airflow:

Inflation time = Airflow

*2 seconds = 35L/s (75 cfm)

*4 seconds = 20 L/s (40 cfm)

*10 seconds = 10 L/s (20 cfm)

However, if you’re using a bigger garbage bag that measures 79 x 119 cm, use this data:

Inflation time = Airlfow

*2 seconds = 100 L/s (210 cfm)

*4 seconds = 50 L/s (105 cfm)

Roofers in Las Vegas

Roofers dont just build or install roofs. They create roofing systems that work the best with the architecture project. A proper roofing system works together as a unit to ensure your buildings overall effectiveness in both shelter and safety. A roofers job is not only to put a roofing system in place, but to repair and maintain it. They will also be able to provide simple solutions for problems you may consider to be bigger than they actually are.

Leaks, Repairs and Replacements

Its inevitable that at some point in time your roof is going to leak. This is caused by damage from weather or just normal wear and tear. Sometimes animals are the cause. But for the most part, a leak in a roof is not uncommon, and you will never find a roof thats completely “leak-proof”. While you may go some years without your roof leaking, eventually its going to happen.

When it does, keep in mind that most of these problems do not require you to re-roof your house. Most leaks are small things, and only require something simple like sealing a crack. A roofer will come in and tell you exactly what the problem is, how they can fix it, how long it will take and how much itll cost.

If, in fact, your roofing system does need to be replaced, it can be for several reasons. An irreversibly repairable roofing system may be the result of neglect, improper material choice, or having a roof installed that is not proper for the building type. If this does happen, you will be told straight away.

The Importance of Annual Inspections

Most of these problems can be prevented by having an inspection done on your roof twice a year. A roofer will come by and make sure that everything is still working on your roofing system the way its supposed to. He can identify minor problems that may be easily repaired right there on the spot, and other problems that may become major ones later on. By listening and following his advice, youll find that things like leaks and repairs will be few and far between, which will save you money in the long run.

Should You Do the Work yourself?

Roofing work should never be done by yourself, unless you are a trained professional. Roofers know the local construction laws and are trained to get their work done with those in mind. You may very well violate something trying to repair your roof yourself and be fined. Or, you can damage the roofing system itself. Or, worse yet, you can get hurt. You should never climb up onto a roof and try to repair or fix anything. Though youve got your finances in mind, investing in proper roof repair is no different than investing in proper care for your car. If you want your home to continue functioning at its peak, then paying a professional to come in and do something no matter how minor is well worth the money spent in the long run.

Bathroom Design Ideas For Adding Or Re-modeling A Bathroom

Whatever the design plans that you have, whether you are planning the addition of a new bathroom, improving an existing one, or even trying to design the layout of a bathroom that is part of the new that you are building for yourself, the designs can range anywhere from the utilitarian to the luxurious. Whenever contractors, architects, and interior designers sketch their plans, they will generally follow standard requirements whatever your preferences, so it is always a good idea to know what they are and how they can affect the layout of your entire home. As more people grow into their retirement years, even more special consideration may be put into adding special features to make it easier to move about and get around. There are a number of great sources when it comes to getting ideas for your bathroom, and while they can be tricky to modify or construct, there are always a few tips for getting the design that is just right for you.

Aim for a specific style and stick to it. It isn’t actually a bad idea if you are looking for a country-themed bathroom design in a country-style home, but keeping the overall theme of your home isn’t entirely necessary though. However it can sometimes be better to design the room separately, while keeping the design and layout requirements in mind. A great idea for getting inspiration for your design is to visit some bathroom showrooms. While you do not really need to incorporate all that you see, it doesn’t hurt to make sure that the design of your bathroom is at least slightly pleasing to the eye, and they always feature the latest trends and fashions. When you start making your purchases for the bathroom project, you may find ideas in home design and remodeling magazines, so if you find any you can clip them out and keep them in a scrapbook for reference.

When hiring a contractor or interior designer to design and build your bathroom, there will be certain specifications that they will be inclined to follow. For example, for a user to be properly accommodated, the preferred toilet height should be around 32 to 43 inches. If an individual is to be able to shower properly inside an interior shower room, it should measure at least 36 by 36 inches. Try to consult with a contractor or interior designer first, before making any modifications to an existing bathroom or adding a new on since they can identify the spatial requirements, as well as design a layout for your bathroom that would properly follow any guidelines. In order to prevent your dream bathroom from turning into a health hazard, your design should follow strict building codes. Re-modelers and builders will usually meet with city authorities for updates about the latest requirements before they tackle a bathroom project.

Advantages and Disadvantages of Built-Up Roofing Systems

Generally, roofs with slants and inclines are favored by most residential and commercial residences. Their natural ability to dispose of rain and snow without having to install substantial amounts of insulation has made them an effective and affordable option.

A built-up roof is an integument made up of alternating layers of tar and asphalt materials. They have been used in the U.S. for almost a century and are usually referred to as tar and gravel roofs, as these are some of the primary materials used in its construction.

Built-up roofing takes coal tar-saturated cotton fabrics and gravel-like materials, like asphalt, to assemble alternating layers of bitumen (tar) and roofing felts or ply sheets directly over the roof decks and insulation. The tar is used to soak into the roofing felt and durably hold all the elements together.

Built-up roofing has been around since the 1840s as a reliable option that was readily available for installing new roofs. All it requires is three essential components: a waterproofing component, a reinforcing component and a surfacing component. Most roofs apply variations of these components to create more durable, waterproof roofs. Some even apply 10 ply sheets to one roof! This helps ensure the roof against potential leaking from entering the home while creating a stable platform for any solar panels or roof gardens installed on the roof.

Built-up roofs are very dependable and work great for many reasons, however, they do have some drawbacks. The maintenance of the roof seems to be the primary concern. Built-up roofs are built flat and as one so when a leak occurs it can be difficult to place the location of it, causing one to have to dismantle the entire roof. 1. In order to avoid major damage, maintenance must take place on the roofing system regularly. Re-asphalting the layers is usually not necessary if the roofing surface is properly cared for. This would include draining the rain that forms on the roof after storms and remodeling the top layer with reflective materials to prevent heat damage.

However, because built-up roofs are flat the task of removing layers are much easier. It also creates flexibility in terms of what you can add to your roofing space, should you so desire. Roofing gardens and solar panels are much more easy to install on flat roofs than traditional sloped rooftops.

Then benefits of this type of roof are great, however, the drawbacks are something to consider. Keep in mind that these roofs require a bit of maintenance and labor, the larger the roof the greater the responsibility for upkeep. If your ultimate goal is to save money, this option would be the most cost-effective.

How To Build A Roof Garden

The concept of a roof garden is not a new one. In fact, it is centuries old!. If you live in an urban area, your dreams of having a garden may be difficult to achieve. Not so if you consider a roof garden!

More and more communities are encouraging their residents to plant roof gardens. The environmental and psychological benefits are numerous. Not only is gardening a calming and relaxing activity, which can reduce stress related illnesses, it also has great benefits for the environment. Building a rood garden on your home or apartment building decrease storm water runoff, reduce fire risks, help decrease heating and cooling costs and can protect your roof from the effects of ultra-violet light and frost.

There are three types of roof gardens and the three types related to the amount of maintenance they require, the depth of soil and the type of plants they will support. They are: Extensive living roofs These are easy to maintain and use little soil. Extensive living roofs are lightweight and lend themselves well for use on sheds, garages and small extensions. As they tend to be harsh environment, suitable plants are ones that are found on cliffs or other harsh environments. While this type of roofs gardens are the easiest to maintain, they also have the least visual appeal. Semi-extensive living roofs These garden roofs are more decorative as they have deeper soils which can support a greater variety of plants. However, the increased soil depth makes these types of roof garden more heavy, so a sound structure is require to support them. They combine the relatively low maintenance of extensive living roofs with a more appealing appearance. Intensive living roofs These are full-fledged gardens and require large and strong support structures.

One of the main considerations when planning a roof garden is the roof itself. While flat roofs lend themselves the best to roof gardens, it is also possible to green pitched, barreled and domed roofs. An easy access to the roof is also important as I am sure you would not be able to enjoy your roof garden as much if you have to climb a ladder every time you want to look at it. The roof must able be able to support heavy loads. Wet soil can weight about eighty pounds per square foot.

Make sure you install a waterproof membrane to avoid ending up with a wet ceiling. The two most commonly used materials are thermoplastic sheeting or rubberized asphalt. As I am certain that you will not want to dig up your garden to replace the membrane every few years, make sure you select a product that is extremely durable. The next layer should be a filter sheet that will allow the moisture to drain off the roof while ensure that the fine material do not escape. Next comes the moisture blanket which will ensure that an extensive live roof garden has enough moisture to support life. Commercial ones can be purchased however it is also possible to use cardboard or old blankets to the same effect.

The following layer will be a drainage layer. Similar to the moisture blanket, it will help retain moisture while allowing excess water to drain away. They are usually made of plastic or geotextile materials. The top layer will be the soils and substrates. These should be lightweight and freedraining yet retain moisture. One such option is an aggregates mixed with light sub-soild such as crushed porous brick or limestone chippings. Finally come the seeds and plants. The possibilities are limited only by your imagination and the environment. Happy gardening!

Slate Cleaner and Removing Glue or Sticky Substances

Removing glue from any surface is hard to do; you want to ensure that youre well informed when it comes to slate cleaner, and getting those gooey messes off your counter. You want to ensure that the glue is removed, but you also want to make sure that you do not ruin the counter top that it is on. Super glue is fast setting, and hard to remove out of the rest of them. Acetone is one of the most used removers for super glue. It can be found in nail polish remover, but nail polish remover might eat away at the stone. You can find it at hardware stores easily now alone. You can put acetone on a swab, and use it to dab the surface of the glue. You will want to apply it in small doses, and carefully not to ruin anything around the surface or the surface itself.

Sticker glue might also be difficult to remove from your stone surface. Getting slate cleaner is beneficial. If you peel the sticker off then a sticky backing might be left behind. Peanut butter is recommended because it removes the stickiness, but it also does not harm the counter tops. This is one of the most loved methods of removing the sticky residue. Vinegar, vegetable, and baby oils work just as well as peanut butter as well. Apply it evenly, and then wipe it off with warm water and a soft cloth.

Rubber cement is hard to remove, but it can be removed with a thinner. You just want to tread lightly when using it since it can eat through the stone. Soaking the glue in the solvent can break apart the glue and remove it from the counter when you use a warm wash cloth and gently wipe it away. School glue is the easiest to remove, and less sticky mess because it cracks when it dries. If you use warm water, it will soften the glue and make it easier to wipe away. This allows you to remove the glue just by wiping it with a damp cloth. You can then use a slate cleaner once the glue is removed.

Once all of this happens, and the glue is removed, you can then go over the place with the slate cleaner and polish. This will allow you to keep the stone clean no matter what gets on it and save the life of your counters.